[PDF&VCE] New Lead2pass 400-101 Dumps PDF Version Released For Free Downloading (701-725)

2016 October Cisco Official New Released 400-101 Dumps in Lead2pass.com!

100% Free Download! 100% Pass Guaranteed!

We never believe in second chances and Lead2pass brings you the best 400-101 Exam Questions which will make you pass in the first attempt. We guarantee all questions and answers in our 400-101 Dumps are the latest released, we check all exam dumps questions from time to time according to Cisco Official Center, in order to guarantee you can read the latest questions!

Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/400-101.html

QUESTION 701
Which two options are contained in the MSG part of a syslog message? (Choose two.)

A.    TAG field
B.    CONTENT field
C.    three-digit priority value
D.    IP address of the sending device
E.    TLS port number

Answer: AB

QUESTION 702
Which two values are needed to configure NTP authentication? (Choose two.)

A.    the encryption method
B.    the key number
C.    the burst mode
D.    the key string
E.    the Diffie-Hellman group

Answer: BD

QUESTION 703
You are configuring a DHCPv6 client for a DHCPv6 server with the prefix delegation feature. Which option is a result of the interface configuration when you enter the command ipv6 address autoconfig default?

A.    a static IPv6 default route pointing to the upstream DHCP server
B.    a static IPv6 default route pointing to the upstream DHCP relay
C.    a static IPv6 default route pointing to the upstream router
D.    a temporary stateless address, formed from the EUI-64 bit address and the prefix from the route advertisement of the upstream router

Answer: A

QUESTION 704
Refer to the exhibit. You are bringing a new MPLS router online and have configured only what is shown to bring LDP up. Assume that the peer has been configured in a similar manner.
You verify the LDP peer state and see that there are no neighbors.
What will the output of show mpls ldp discovery show?
7041

A.    Interfaces:
Ethernet0/0 (ldp): xmit
B.    Interfaces:
Ethernet0/0 (ldp): xmit/recv
LDP Id: 25.25.25.2:0; IP addr: 192.168.12.2
C.    Interfaces:
Ethernet0/0 (ldp): xmit/recv
LDP Id: 192.168.12.2:0; no route
D.    Interfaces:
Ethernet0/0 (ldp): xmit/recv
LDP Id: 25.25.25.2:0; no route

Answer: D

QUESTION 705
Which three features are common to OSPF and IS-IS? (Choose three.)

A.    They both maintain a link-state database from which a Dijkstra-based SPF algorithm computes a shortest path tree.
B.    They both use DR and BDR in the broadcast network.
C.    They both use hello packets to form and maintain adjacencies.
D.    They both use NSSA and stub type areas to scale the network design.
E.    They both have areas to form a two-level hierarchical topology.

Answer: ACE

QUESTION 706
Refer to the exhibit. Which two commands are required on R3 in order for MPLS to function? (Choose two.)
7061

A.    mpls ip
B.    ip cef
C.    mpls label protocol tdp
D.    mpls ip propagate-ttl

Answer: AB

QUESTION 707
Which two statements about the assert process in LAN-based PIM are true? (Choose two.)

A.    If the metrics are the same, the router with the lowest advertised routing protocol metric for that route is elected.
B.    If the metrics are the same, the router with the highest IP address on the LAN is elected.
C.    If the metrics are the same, the router with the highest advertised routing protocol metric for that route is elected.
D.    If the metrics are the same, the router with the lowest IP address on the LAN is elected.

Answer: AB

QUESTION 708
Which two options are the two underlying protocols on which a DMVPN relies? (Choose two.)

A.    IPsec
B.    NHRP
C.    GDOI
D.    ISAKMP
E.    SSL
F.    NLRI

Answer: AB

QUESTION 709
Which three parameters must match to establish OSPF neighbor adjacency? (Choose three.)

A.    the process ID
B.    the hello interval
C.    the subnet mask
D.    authentication
E.    the router ID
F.    the OSPF interface priority

Answer: BCD

QUESTION 710
Which IP SLA operation type uses IP to measure the round-trip time between a router and a device?

A.    HTTP
B.    ICMP Echo
C.    ICMP Path Jitter
D.    UDP Jitter for VoIP

Answer: B

QUESTION 711
What are two reasons to use the ip ospf database filter all out command? (Choose two.)

A.    to maintain a centralized OSPF database on a single master device
B.    to avoid flooding LSAs on low-speed links
C.    to ensure a consistent OSPF database across the network
D.    to selectively filter OSPF routes without disrupting the SPF algorithm
E.    to filter only type 7 LSAs from an OSPF area
F.    to enable OSPF to send triggered updates

Answer: AB

QUESTION 712
On a broadcast interface, which two OSPF states support BFD sessions? (Choose two.)

A.    DR
B.    BDR
C.    DROTHER
D.    2WAY
E.    FULL
F.    ACTIVE

Answer: AB

QUESTION 713
Which two statements about BGP best-path selection are true? (Choose two.)

A.    The route with the highest local preference is preferred.
B.    The weight attribute is advertised to peers.
C.    The route with the lowest MED is preferred.
D.    A route that originates from iBGP peers is preferred.
E.    A route that originates from a router with a higher BGP router ID is preferred.
F.    The lowest weight advertised is preferred.

Answer: AC

QUESTION 714
The no ip unreachables command is configured on interfaces to protect the control plane of a router.
Which mechanism is impacted by using this command?

A.    ICMP redirects
B.    path MTU discovery
C.    source routing
D.    ICMP router discovery protocol

Answer: B

QUESTION 715
Refer to the exhibit. The customer wants to use IP SLA to create a failover to ISP2 when both Ethernet connections to ISP1 are down. The customer also requires that both connections to ISP1 are utilized during normal operations.
7151
Which IP route configuration accomplishes these requirements for the customer?

A.    ip route 0.0.0.0 0.0.0.0 192.168.0.1 track 1
ip route 0.0.0.0 0.0.0.0 192.168.1.1 track 2
ip route 0.0.0.0 0.0.0.0 192.168.2.1 track 3
B.    ip route 0.0.0.0 0.0.0.0 192.168.0.1 track 1
ip route 0.0.0.0 0.0.0.0 192.168.1.1 track 2
ip route 0.0.0.0 0.0.0.0 192.168.2.1 track 4 100
C.    ip route 0.0.0.0 0.0.0.0 192.168.0.1 track 1
ip route 0.0.0.0 0.0.0.0 192.168.1.1 track 2
ip route 0.0.0.0 0.0.0.0 192.168.2.1 track 3 100
D.    ip route 0.0.0.0 0.0.0.0 192.168.0.1 track 1 1
ip route 0.0.0.0 0.0.0.0 192.168.1.1 track 2 2
ip route 0.0.0.0 0.0.0.0 192.168.2.1 track 3 3

Answer: C

QUESTION 716
Which statement describes what it means if a router has an OSPF priority set to 0?

A.    A router with the OSPF priority set to 0 is one that can participate in the election of a DR. It has the highest priority.
B.    A router with the OSPF priority set to 0 is one that cannot participate in the election of a DR, but it can become a BDR
C.    A router with the OSPF priority set to 0 is one that cannot participate in the election of a DR. It can become neither a DR nor a BDR.
D.    A router with the OSPF priority set to 0 is one that cannot participate in the election of a BDR, but it can become a DR

Answer: C

QUESTION 717
What is the maximum number of classes that MQC can support in a single policy map?

A.    512
B.    256
C.    128
D.    64

Answer: B

QUESTION 718
Drag and Drop Question
Drag each IPv6 extension header on the left to its corresponding description on the right.
7181
Answer:
7182

QUESTION 719
Drag and Drop Question
Drag each traceroute text character on the left to its meaning on the right.
7191
Answer:
7192

QUESTION 720
Drag and Drop Question
Drag and drop each IPv6 neighbor discovery message type on the left to the corresponding description on the right.
7201
Answer:
7202

QUESTION 721
Drag and Drop Question
Drag and drop each BGP feature on the left to the corresponding function it performs on the right.
7211
Answer:
7212

QUESTION 722
Drag and Drop Question
Drag and drop each DHCP term on the left to the corresponding definition on the right.
7221
Answer:
7222

QUESTION 723
Drag and Drop Question
Drag and drop each step of the Unicast RPF process on the left into the correct order on the right.
7231
Answer:
7232

QUESTION 724
Drag and Drop Question
Drag and drop the SNMP element on the left to the corresponding definition on the right.
7241
Answer:
7242

QUESTION 725
Drag and Drop Question
Drag and drop each PHB on the left to the functionality it performs on the right.
7251
Answer:

7252

Lead2pass new released 400-101 PDF are now for free download, download it right now and pass your exam 100%.

400-101 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDU2RjeUlHTTZXb1U

2016 Cisco 400-101 exam dumps (All 1219 Q&As) from Lead2pass:

http://www.lead2pass.com/400-101.html [100% Exam Pass Guaranteed]

You may also like